Drop Tester

详情

VS****8
* This tester is pneumatic controlled that makes the controlling accurately. Maximum payload: *5Kg; test height: *****0cm; support arm size: *9x*0cm; power source: **0V, *0/*0Hz, single phase; pneumatic requirement: higher than 5kg/cm2.
* Escalate mechanism: adopt motor drive to adjust height.
* Testing angles: to drop the package based on its corner, face, and edge.
* Protecting switches: used to prevent the collision of tester’s mechanical parts from moving over the upper and lower limits of guiding rod.
* Tape measure: **0 cm tape measure is used to cope with indicator in reading the practical elevating and lowing height instantly.
* Bear plate: the whole plate adopts aluminum alloy for anti-oxidation and drops with small noise.
* Control : adopts -typed magnetic switch that allows the bear plate to fall automatically when pushing “DROP” and also to adjust its height.
* Screw rod: adopts cylindrical screw rod design for smoothing up and down movement of bear plate.
* Control box: the control box is separated from the machine to prevent the operator from injury during the dropping of testing sample
* Guiding rod : one ψ**0㎜ grinding rod used to prevent drop tester from swinging around.
* Horizontal level: there are four horizontal level used to adjust plane level of the base.
* Additional item 1: Clip fixture, especially for portable device.
* Additional item 2: Digital control box, that can control the lift automatically in order to solve the problem of indicating the height of higher than **0cm.

VS****3
* Dropping Ball: ***1g (diameter: *0.8mm), cylinder with spheric impacting face, control by electromagnet
* Test height: ****0cm, free fall
* Tape measure: **0 cm tape measure is used to cope with indicator in reading the practical height instantly.
* Bottom plate: adopts steel that can prevent from jumping when impact, the dimension is **0x**0mm
* The fixture and above can design for your need.

VS****5
* Maximum Impact Force: ***0Kgf (*5,**0N)
* The impact force and velocity can be adjusted and measured to display on panels.
* Impact Distance: about 1m, operate by high-pressure cylinder to do in such short distance
* Peripheral Device: enclosed container, with a tempered glass view window, a  inside light, a blower with a *-m air tube and a adjusted fixture.
* Testing videos please go to youtube and search username 'vibsource'.

VS****7
* This tester is magnetic controlled to let the specimen to free fall. Maximum payload: *5Kg; test height: *****0cm; applicable specimen size: *0x*0x*0cm; power source: **0V, *0Hz, single phase.
* Escalate mechanism: adopt motor drive to adjust height.
* Testing angles: to drop the package based on its corner, face, and edge.
* Protecting switches: used to prevent the collision of tester’s mechanical parts from moving over the upper and lower limits of guiding rod.
* Tape measure: **0 cm tape measure is used to cope with indicator in reading the practical elevating and lowing height instantly.
* Bear plate: the whole plate adopts aluminum alloy for anti-oxidation and drops with small noise.
* Control : adopts -typed magnetic switch that allows the bear plate to fall automatically when pushing “DROP” and also to adjust its height.
* Screw rod: adopts cylindrical screw rod design for smoothing up and down movement of bear plate.
* Control box: the control box is separated from the machine to prevent the operator from injury during the dropping of testing sample
* Guiding rods: three grinding rods, in the middle, left and right position, used to prevent drop tester from swinging around.
* Horizontal level: there are four horizontal level used to adjust plane level of the base.

VS****9
* This tester is pneumatic controlled that makes the controlling accurately. Maximum payload: **0Kg; test height: ****0cm; support arm size: **0x**0 cm; power source: **0V, single phase; pneumatic requirement: higher than 5kg/cm2.
* Escalate mechanism: adopt motor drive to adjust height.
* Testing angles: to drop the package based on its corner, face, and edge.
* Protecting switches: used to prevent the collision of tester’s mechanical parts from moving over the upper and lower limits of guiding rod.
* Tape measure: **0 cm tape measure is used to cope with indicator in reading the practical elevating and lowing height instantly.
* Bear plate: **5 frames a set and all adopt aluminum alloy for anti-oxidation and drops with small noise.
* Control : adopts -typed magnetic switch that allows the bear plate to fall automatically when pushing “DROP” and also to adjust its height.
* Screw rod: adopts cylindrical screw rod design for smoothing up and down movement of bear plate.
* Control box: the control box is separated from the machine to prevent the operator from injury during the dropping of testing sample
* Guiding rod : three ψ**0㎜ grinding rods used to prevent drop tester from swinging around.
* Horizontal level: there are four horizontal level used to adjust plane level of the base.