Split sperated high pressurized solar water heater

详情

Split sperated high pressurized solar water heater 

Features:
The system could be mounted on the southern roof of the villa，on the courtyard lawn, or the southern slope of the construction. The hot water could be delivered to any floor without limitation. The system has adopted the forced circulation (automatic control) work module to control the temperature automatically and deliver water by pressurization. So it has solved the long time inconveniences of manual operation. The system only needs small amount of investment, and it's easy to handle. Moreover, it's safe, convenient and energy saving, causing no pollution to the environment, so it's complemented as Green Project by the experts.
 
The composition of the system：
The solar water heating system is consisted of solar collector, heat preservation water tank, solar power workstation and the pipe. The solar collector is consisted of super conducting vacuum heat collecting tube and header, so it's of great efficiency of heat collecting. The absorbing percentage of the glass vacuum collector is more than *4%. In the sunny days of spring or autumn, each collecting tube could make the water up to *0℃only in 2.5 hours. The water tank uses SUS **4 2B stainless steel as internal bladder and polyurethane integral foaming as heat preservation material to improve the heat preservation ability. And it makes the system be used as usual under minus *0 ℃. The high corrosion-resistant and good heat preservation PPR pipe is used as the system's pipe, so it adds the good efficiency and long service of the system.
 
The principle of the system：
1.The collector applies the fourth generation of solar collector**-heat pipe vacuum collector to transfer the solar power to heat energy.
2. When the temperature of TC(the temperature of the collector) is higher than that of TR(the temperature of the water tank), the controlling device will start the circulating pump.
3. The circulating pump makes the working medium circulate in the system. 
4. The heat is transferred from the heat collector to the water tank by the heat exchanger
5. During the working process of the circulating pump, when the temperature difference is less than a set point, the circulating pump will stop. 
6. When TR (the temperature of the water tank) reaches the highest of set point, the controlling device will close the circulating pump. 
7. The electrical heating device will automatically make the temperature of the above part of water tank stay at the set point.
 
The characteristics：
1. The collector and the water tank are separated, and the system runs under the forced pressure. 
2. The controlling device is specialized, so the system runs automatically.
3. The water tank can be installed anywhere.
4. The heat pipe vacuum tube collector is two circuit system, free of freezing and could be used all year.
5. The metal super*- conducting vacuum heat collector is used, no water in the tube, no bursting and could be used as usual under minus*0℃. 
6. The water tank applies with the enamel internal bladder, runs under pressure.
7. Provide the water at the same temperature, set the highest temperature, heat the water at set point by electricity, protecting the data when power off, supply the hot water *4 hours a day.
8. The system is designed separately, in harmony with the structure. 
9. The heat collector could be mounted on the balcony veranda, the southern wall, sloping roof or awning.
*0. The system is designed as unit, convenient to transport.
The characteristic of each part：
1.Heat collector: Sectional metal vacuum heat pipe collector.
2. The water tank: Enamel internal bladder electrical water tank.
3. The circulating pump: UPS system imported from Germany, energy saving, low noise and long service. 
4. The frame of heat collector and the water tank.
5. The controller: imported from Germany, stable and complete in function.
6. The workstation: The main parts are imported from Italy to ensure the safe and reliable running of the closed system.
7. The pipe: the copper tube is suggested.
8. The heat preservation material.
The principle of the follow chart:
Manifold Casing Material    **4 Stainless Steel of Powder Coated Aluminium
Frame Material    **4 Stainless Steel. or aluminum alloy
Header Pipe Material    C****0 Copper
Insulation    Polyurethane *5mm
Rubber Seals and Rings    UV stabilized high temperature silicon rubber
Optimal installation angle    ****0°Vertical,0°Horizontal
Maximum Operating Pressure    6bar**5psi
Pressure Drop    *@******************** manifold(SRCC)
Optimal flow rate    0.1L/min/tube*0.**6G/min/tube
Performance Data(SPF)    Conversion Factor: ho=0.**7
Loss Coefficients:a1=1.*2,a2=0.***5

Collector:

Glass evacuated tube Technique specification:
◎Material: borosilicate glass according to ISO***5:***1;transmittance of borosilicate glass:0.*2.Absorbance of solar selective 
absorptive coating:0.*4;Hemispherical emittance:0.*8;Getter according to GB/T********8.
◎Start-up temperature: no more than *5℃.
◎Start-up time: no longer than 2 minutes under normal sunshine.
◎Low temperature resistance: no breaks at**0℃
◎Heat impact resistance: no damages after over 3 times' alternative impacts of cold water below *5℃ and hot water over *0℃.
◎Pressure resistance: can withstand 0.6Mpa.
◎Hail resistance: no damage by the impact of Φ*5mm hail.
◎Appearance standard: the color of the selective absorptive coatings should be even, and the coatings should have no wrinkles and peelings. The allowed tolerance of borosilicate glad glass tube's diameter should be in accordance with ISO***3:***8.camber of the borosilicate glass tube should be no more than 0.3%.The translation the borosilicate glass tube, which is ****0mm away from flange end, should be round. The ratio of the longest to the shortest radial dimensions of the borosilicate glass tube should be no more than 1.*2.
Water Tank:
1.Polyethylene insulation with a fabric casing can be used if polyurethane insulation is not suitable.
2. Tanks are designed for high pressure that direct connection to mains pressure water supply is permitted.
3. Direct connection of copper coil HE to mains pressure water supply is permitted. 
4. In most regions, only locally approved heating elements can be used. The heating element port can be made as customers required to suit any sized element. (Female thread-located in top of tank).A sample of the heating element will need to be provided before tanks are manufactured in order to.