Sequin Punching Machine

详情

Richpeace is in the position to offer you an effective sequin punching machine for making chain sequin applied in computerized embroidery machine with sequin device. The following is the details of this machine. 1.Usage Spangle punching press is an auxiliary apparatus for fabric finishing , mainly used to punch fail tape to produce spangle strip for future use. ***** parameters Main motor power:1.5Kw Reducer type: BWD***5.**1.5Kw Auxiliary motor type : *0 YYJT*0/*0GK*0 Auxiliary motor power : *0*2=**0w Power supply: **0V/**0Hz Stroke: 8mm Mould closed height: *5mm Punch: **0 punch/min Foil width : **5mm 3.Structure and principle (pls find attached picuture of manual) Through the triangle belt, the motor drives the eccentric sleeve to rotate the crank and eccentric sleeve both installed on the shaft .The crank transfers the motion to float plate, Slide lever and upper float plate. The float plate, slide lever and upper float plate begin the reciprocating motion. The mould installed on the upper float plate punch the foil tape to produce spangle strip ***** and adjustment The installation is very simple. First , find a space to install the machine then drill four holes and locate ground belts. Adjust the device to level. The last step, fasten the M*2 screws to fix the device. (pls find the attached picture of manual) 5. The control panel(pls find the attached picture of manual) 6. Operation process 6.1 Put the mould to the space between the top plate and upper float plate , align the hole on the mould with the hole on the top plate and upper float plate. Using M*0 screw, washer and spring washer, fix the convex halt mould on the upper float plate and concave half mould on the top plate, fasten the screws. Attention the direction of the mould: do not overturn the mould. The half has square hole is concave half mould. The foil tape inlet slot of the mould face to foil tape feed unit .The spangle strip outlet slot (Separated into several little slots by ribs) of the mould face to spangle tape-winding unit. 6.2 Check the spangle punching press and mould carefully , if any fastener loosened, fasten it . 6.3 Put the plastic plates between the space of the two �*8 shafts of the spangle strip-winding unit. Notice: line up enough plastic plates to fill in the space. The central line of the plastics plates parallel with the central line of the two �*8 shafts .If the plastic plates are not enough , they will fall down , so they can not rub with the two�*8 shafts to make themselves rotating . 6.4 Put the foil scroll (width:**5mm) onto the shaft sleeves of the foil tape feed unit. Put the one end of the **5mm foil tape into the inlet slot of the mould .Notice: operate by manual before the punched spangle strips winding onto the plastic plates of the winding unit . 6.5 Before the power is on , turning the hand wheel by manual , letting the mould punch to and fro, foil tape feeding in by hand, observe whether the mould work is in good condition and whether pattern of the spangle is correct . Notice: after sever at punch , if you find spangle strip still cannot come from the other side of the mould and the foil tape block by die head you must adjust the stroke of spangle punching machine . The method is : disassemble the guard sheet metal of the machine, adjust the adjustment screw to get suitable mould stroke. (pls find the attached picture of manual) 6.6 Switch on the power. The power indication lamp is on 6.7 Input the punch number you wanted through pressing two and - little button on counter. Notice: if the punch numbers you input is 0, the machine will not run at all. 6.8 Switch on the button of spangle strip-winding unit and the button of foil tape feed uni . Turn the knob of spangle strip-winding unit to get suitable winding speed . Turn the knob of foil tape unit to get suitable feeding speed. Notice: the feeding switch has manual and auto two post . Switch the button to manual, the feeding motor run continually; Switch the button to auto, only while the foil tape touch the wire of touch switch , the feeding motor get the signal begin to run .when the machine is at normal work , feed switch at auto post and the foil should go through below the wire of the contact switch . Press the jerk button; observe the machine and the mould whether under harmonious condition. If nothing is wrong , press punch button to start , switch winding switch to on post; switch feeding switch to auto post .the punch work begins. Wind the punched spangle strip to plastic plates. When the punch work finishes , press punch stop, switch winding switch to off post, pressing jerk button , do not let the mould close too tightly. Switch off the power. 7. Maintenance 7.1 keep the machine cleaning . 7.2 check the triangle belt regularly 7.3 Lubricate slide levers and guide bushes **4 times per 8 hours. 7.4 Bearings and reducer need routine maintence. 7.5 Open the mould and spray anti-corrision oil if long time do not use it. Put the mould to a dry place. If there is anything you are not clear, please contact us. We will give you our best sevice. You also don&#**9;t need to worry about the quality.