离岸价格
获取最新报价|
Minimum Order
位置:
jinan,shandong,china
最小订单价格:
-
最小订单:
1 Set
包装细节:
wooden case or on request
交货时间:
30-90 days
供应能力:
200 Set per Year
付款方式:
T/T, L/C
联系人 candice
Jinan, Shandong
1.BRIEF
INTRODUCTION
As an integrator of hammer mill and impact mill, PCFK series of
Impact Hammer Mill is used for secondary crushing of low- and
medium-hardness materials. The size of material can be reduced from
<*0mm to <8mm. The mill enjoys advantages in high and
constant capacity, excellent uniformity of final grain size, low
fine grain content and etc.
2.MODE OF OPERATION
The uniform distribution of the feeding material at the entire
width of the rotor via a vibrating feeder or
a specially-designed inlet chute is requested for achieving an
optimum final grain size as well as a uniform wear of the crushing
parts. After entering the crushing cavity, the feed material is
grasped by the rotating beater heads and then thrown against the
grinding face at high speed to be crushed and again rebound to
beater heads. The material is gradually crushed in a course of dash
and inter-collision repeatedly and discharged out of the end of
grinding face. Product size is determined by rotation speed of the
rotor and gap between the rotor and the grinding wall.
| Mill Type | PCFK***0 | PCFK***2 | PCFK***4 | |
| Feed Materials | Coal, coke, limestone, gypsum,salt, ore and etc. | Coal, coke, limestone, gypsum,salt, ore and etc. | Coal, coke, limestone, gypsum,salt, ore and etc. | |
| Size of Feed Material (mm) | ≤*0 | ≤*0 | ≤*0 | |
| Product Size (mm) | ≤8(*5%≤3) | ≤8(*5%≤3) | ≤8(*5%≤3) | |
| Diameter of Rotor (mm) | ***0 | ***0 | ***0 | |
| Length of Rotor (mm) | ***0 | ***0 | ***0 | |
| Capacity(t/h) | ****0 | ****5 | *****0 | |
| E-motor | Type | Y**5M*6 | Y**5M**6 | YKK*****6 |
| Power(KW) | *0 | **5 | **0 | |
| Rotation Speed(rpm) | **0 | **0 | **0 | |
| Voltage (V) | **0 | **0 | **0 | |
| Fluid Coupling | YOX**0 | YOX**0 | YOX**0 | |
| Mill Type | PCFK***2 | PCFK***6 | PCFK***8 | |
| Mill Type | PCFK***0 | PCFK***2 | PCFK***4 | |
| Feed Materials | Coal, coke, limestone, gypsum,salt, ore and etc. | Coal, coke, limestone, gypsum,salt, ore and etc. | Coal, coke, limestone, gypsum,salt, ore and etc. | |
| Size of Feed Material (mm) | ≤*0 | ≤*0 | ≤*0 | |
| Product Size (mm) | ≤8(*5%≤3) | ≤8(*5%≤3) | ≤8(*5%≤3) | |
| Diameter of Rotor (mm) | ***0 | ***0 | ***0 | |
| Length of Rotor (mm) | ***0 | ***0 | ***0 | |
| Capacity(t/h) | ****0 | ****5 | *****0 | |
| E-motor | Type | Y**5M*6 | Y**5M**6 | YKK*****6 |
| Power(KW) | *0 | **5 | **0 | |
| Rotation Speed(rpm) | **0 | **0 | **0 | |
| Voltage (V) | **0 | **0 | **0 | |
| Fluid Coupling | YOX**0 | YOX**0 | YOX**0 | |
| Mill Type | PCFK***2 | PCFK***6 | PCFK***8 | |
