详情
Heating-proof
sandwich compound production line can combine thin high intensity
materials with thicker but lighter materials in single or
double sides to form a new building material which has the
advantages of high intensity、lighter、strong、durable、beautiful
outlook. Generally the outside material could be color steel sheet
(thickness:0.3mm*0.8mm)、stainless steel、aluminum、plastics panel and
so on, while inner part uses thicker(thickness: *****0mm)but
lighter materials such as EPS frothed self-extinguished
polystyrene、frothed polyurethane. Heating proof sandwich board is a
new building material with multifunction such as warm
keeping、lighter、water-resistant、decoration and bearing. It is now
widely used on public construction、factory、large size warehouse、big
span roof、wall decoration、various refrigeratory、cleans room、air
conditioner room…
ZSF metal heating
proof sandwich board production line can produce H section and
self-buckle section panel and corrugated section sandwich
panel.
二、Components
of ZSF production line
ZSF metal heating
proof sandwich production line includes:
1 set of ZSF main
machine
Corrugated panel
forming machine(different model choices )
1 Holding
frame
1 cover-hat type
machine(optional)
1 colored sheet
stripper machine(optional)
1 panel cutting
machine (optional)
1 lockstitching
border machine (optional)
1 set of feeding
frame (1 big 1 small)
4 clamping plate
machines(2 big 2 small)
三、Technical
data of production line
1.Dimension :(LxWxH)
****0x***0x***0
2、 Production
ability
Speed:**4.5m/min(depends
on adhesive foam speed)
(Generally speaking
,production speed is between 1.5m/min and 2.5m/min)
Yearly
production ability: *****0 m2
3、Machine
weight:*6Mt
4、Machine character:
Horizontal type, uninterrupted production, stepless frequency
conversion speed adjustment, regular length cut, electrical
heating;
5、Installed capacity:
(electrical heating type) *8KW,AC**0V ,*0HZ
6、Working condition:
workshop square ***0m2,main machine working environment temperature
is higher than *0°C.(Celcius)
7、Adhesive
use
Use computation pump
to mix adhesive. Dript the adhesive on the roll plate before
plastering evenly.
The adhesive quantity
is from 0.*5 to 0.4kg/m2
8、Available steel plate
thickness:0.**0.8mm
9、core plate
thickness:*****8mm
*0、 Available steel
plate width:***0mm ***0mm ***0mm
(wallboard)：
***0/***0 ***0/***0
***0/***0
(roof
plate)：***0/***0 ***0/***0
*1、Length automatic
set、quantity automatic
accumulate， automatically turn off after finish
producing.
四、：
Workshop
requirement
1、Workshop
Workshop sketch
map
◇ Flat
or spired roof workshop, cornice should be higher than
5m
◇ Effective
width no less than 8m
◇ There
should be a compressed air resource
(0.**0.6m3*7Kg/min)
2、(Power
supply)
◇ Three
phrase five line system to supply power, zero conductor should be
separated from ground wire all the time, grounding resistance less
than 4Ω.
3、Crane
◇ Equipments
installed within the working area of traveling crane are
available,
◇ Weight
lift more than 5Mt.
◇ Lift
height(hook bottom) is 3.9m higher over machine sets
floor.
4、PersonnelDaily
maintenance needs *2 persons, among them **5 are key working
procedure persons.
5、Materials
①
Plate
△ ***0*5mm、***0*5mm、***0*2mm、**3*2mm等。
△ Normally
the width is ***0*5mm、***0*5mm、***0*2mm、**3*2mm.△ Thickness
is 0.**0.6mm.
△ Each
roll weighs about 5mt,coil diametersΦ**0 &
Φ**0.
△ **0mm、和**5mm。厚度为0.6mm。
△ Edge
strip width is *5mm，**0mm、**5mm,thickness
is 0.6mm
② 芯材Core
material
△ Normally
use EPS plate or fiberglass plate.
△ For
EPS the density is not less than ***6kg/m3.
△ For
fiberglass the density is not less than *6kg/m3
△ The
oxygen index of EPS self extinguished core material should be
bigger than *0
③PU adhesive A &
B, mixed when needed, the strength should be more than
*0N/cm.Adhesive should be kept clean and oxygen index more than
*0.Group A Sticky
liquid with yellow appearance
(Viscosity)NO
0.**0.7PaS UC**0
Group B Sticky
liquid with brown appearance
(Viscosity)NO
0.**0.6PaS
The mix
ratio between A&B is 1:1.5
