This
2 channel DC RF wireless remote control system can used to control
lights, motor, fans, electrically operated doors/locks blinds or
other appliances automatically. It is easy to install and use. The
remote control switch has 2 buttons, and works with toggle,
latched, momentary and momentary + toggle 4 control modes. Its
control distance is about **0 meters away. It should be a good
choice for you. Just take it
away! Note: Customized design is acceptable, we
have professional
technology-support! Feature:
Wireless control, easy to
install
Control
Lights, Motors, Fans, electrically operated
Doors/Locks/Windows/Blinds/Cars or Other Appliances with AC
**0~**0V or DC 0~*8V.
You can turn on/off the receiver with transmitter (remote
control) from any place within a reliable distance; the wireless RF
signal can pass through walls, floors and doors.
With characteristics of over current protection, short-circuit
protection and temperature protection.
Audible /
visual indication
Use
microcontroller model of EM*8P**6, an *-bit microprocessor designed
and developed with low-power and high-speed CMOS
technology.
Reliable control: The transmitter (Encoding) and the receiver
(Decoding) use an *-bit code.
One/several transmitters can control one/several receivers
simultaneously.
If you use two or more receivers in the same place, you can set
them with different codes.
Transmitting Frequency: The default frequency is **5MHz
,we can also provide **3MHz, you can leave
us a message or contact us if you need.
Receiver:
Model No.: H*-DC*2
Channel: 2 CH
Control Modes: Toggle, Momentary, Latched, Momentary +
Toggle
Coding Type: Fixed code
Coding Setting: By learning
Power Supply (Operating Voltage): DC*2V±1V
(H*-DC*2),we can also provide DC*9V or DC*4V,please
contact us if you need.
Working Voltage Range of Relay: AC **0~**0V or DC 0~*8V
PCB size: *4mm x *2mm x *4mm
Case size: *9mm x *8mm x *5mm
Maximum Working Current: *0A
Transmitter:
Model No.: HR**2
Channel: *2 CH
Remote Control Distance:
***0m / ***0ft (theoretically)
Encode: Fixed code by
Soldering
Unit size: **5mm x *4mm x
*5mm
Power Supply: 1 x 6F*2 *9V
battery (included, can be used for *2 months)
Usage:
Setting different control
modes (We have set the receiver as Toggle control mode before
delivery. If you want to use other control modes, do as following
operation):
Setting control mode
Toggle: Only connect Jumper*2.
Control mode Toggle: Press -> On; Press again -> Off.
Press button A: Turn on the relay (connect B and C, disconnect A
and B)
Press button A again: Turn off the relay (disconnect B and C,
connect A and B)
Setting control mode
Momentary: Only connect Jumper*1.
Control mode Momentary: Press and hold -> On; Release ->
Off.
Press and hold button A: Turn on the relay (connect B and C,
disconnect A and B)
Release button A: Turn off the relay (disconnect B and C, connect A
and B)
Setting control mode
Latched: Do not connect Jumper*1 and Jumper*2.
Control mode Latched: Press -> On, another relay Off; Press
another button -> Off.
Press button A: Turn on the relay (connect B and C, disconnect A
and B)
Press button B: Turn off the relay (disconnect B and C, connect A
and B)
Setting control mode
Momentary + Toggle: Connect Jumper*1 and Jumper*2.
Control mode Momentary (Channel 1): Press -> On; Press again
-> Off.
Press and hold button A: Turn on relay 1 (connect B and C,
disconnect A and B)
Release button A: Turn off relay 1 (disconnect B and C, connect A
and B)
Control mode Toggle (Channel 2): Press and hold -> On; Release
-> Off.
Press button B: Turn on relay 2 (connect B and C, disconnect A and
B)
Press button B again: Turn off relay 2 (disconnect B and C, connect
A and B)
We have learned
remote control to the receiver. If you don’t want the receiver to
work with the remote control, you can delete all codes of remote
controls, which are stored in the receiver. Operation: Press and
hold the button of receiver until signal LED flashes slowly;
release the button, LED keeps slow flash. That means all stored
codes have been deleted successfully.
Learning the button of
remote control: 1) Press the button of
receiver; signal LED on the receiver keeps shining. The receiver
enters into status of LEARNING. 2) Press button on
remote control. If signal LED flashes quickly *5 times and turns
off, it means learning is successful. Receiver1:press button 1 to
learn. Receiver2:press button 3 to
learn. Receiver3:press button 5 to
learn. Receiver4:press button 7 to
learn. Receiver5:press button 9 to
learn. Receiver6:press button 1 to
learn. 3) When receiver is in
the status of LEARNING, press again the button of receiver, signal
LED turns off, learning process will be discontinued. 4) The receiver can
learn several remote controls with different codes.
Package
included:
*2 x Receiver: H*-DC*2 (2
Channel / Four Control Modes)
