Note:Customized
design is acceptable, we have professional
technology-support! Feature:
Wireless control, easy to
install
Control
Lights, Motors, Fans, electrically operated
Doors/Locks/Windows/Blinds/Cars or Other Appliances with AC
**0~**0V or DC 0~*8V.
You can turn on/off the receiver with transmitter (remote
control) from any place within a reliable distance; the wireless RF
signal can pass through walls, floors and doors.
Audible /
visual indication
Use
microcontroller model an *-bit microprocessor designed and
developed with low-power and high-speed CMOS
technology.
Reliable control: The transmitter (Encoding) and the receiver
(Decoding) use an *-bit code.
One/several transmitters can control one/several receivers
simultaneously.
If you use two or more receivers in the same place, you can set
them with different codes.
Transmitting Frequency: The default frequency is **5MHz
,we can also provide **3MHz, you can leave
us a message or contact us if you need.
Working Voltage Range of Relay: AC **0~**0V or DC 0~*8V
PCB size: *3mm x *3mm x *8mm
Case size: *9mm x *9mm x *8mm
Maximum Working Current: 5A(each channel)
Transmitter:
Model No.: HR*2
Channel: *2CH
Remote Control Distance:
***0m / ***0ft (theoretically)
Encode: Fixed code by
Soldering
Unit size: **5mm x *2mm x
*5mm
Power Supply: 1 x
6F***9V battery (included, can be used for *2 months)
Usage:
We have learned
remote control to the receiver. If you don’t want the receiver to
work with the remote control, you can delete all codes of remote
controls, which are stored in the receiver. Operation: Press and
hold the button of receiver until signal LED flashes slowly;
release the button, LED keeps slow flash. That means all stored
codes have been deleted successfully. Learning the button of
remote control: 1) Press the button of
receiver; signal LED on the receiver keeps shining. The receiver
enters into status of LEARNING. 2) Press any one
button on remote control. If signal LED flashes quickly *5 times
and turns off, it means learning is successful. 3) When receiver is in
the status of LEARNING, press again the button of receiver, signal
LED turns off, learning process will be discontinued. 4) The receiver can
learn several remote controls with different codes
Setting different control
modes (We have set the receiver as Toggle control mode before
delivery. If you want to use other control modes, do as following
operation):
1) Learning Toggle control mode: When the
receiver is in the status of LEARNING, press button 1 of the remote
control. Control mode Toggle (Channel
1~*2): Press -> On; Press again -> Off. Press button 1: Turn on relay 1
(connect B and C, disconnect A and B) Press button 1 again: Turn off
relay 1 (disconnect B and C, connect A and B) … Press button *2: Turn on relay *2
(connect B and C, disconnect A and B) Press button *2 again: Turn off
relay *2 (disconnect B and C, connect A and B) 2) Learning Momentary control
mode: When the receiver is in the status of LEARNING, press button
2 of the remote control. Control mode Momentary (Channel
1~*2): Press and hold -> On; Release -> Off. Press and hold button 1: Turn on
relay 1 (connect B and C, disconnect A and B) Release button 1: Turn off relay
1 (disconnect B and C, connect A and B) … Press and hold button *2: Turn on
relay *2 (connect B and C, disconnect A and B) Release button *2: Turn off relay
*2 (disconnect B and C, connect A and B) 3) Learning Latched control mode:
When the receiver is in the status of LEARNING, press button 3 of
the remote control. Control mode Latched (Channel
1~*2): Press -> On, other relays Off; Press other button ->
Off. Press button 1: Turn on relay 1
(connect B and C, disconnect A and B) Turn off other relay (disconnect
B and C, connect A and B) ……………… …………
