看起來你不是TradeKey.com的會員。 立即註冊,與全球超過7百萬的進口商和出口商建立聯繫。 点击注册--免费! |
BOOK A CALL
Book Call On Your Favorite Time
Code
🗘

By Signing Up. I agree to TradeKey.com Terms of Use, Privacy Policy, IPR and receive emails related to our services

Contact Us
128 Printhead Cleaner

128 Printhead Cleaner

离岸价格

获取最新报价

|

Minimum Order

位置:

-

最小订单价格:

-

最小订单:

-

包装细节:

-

交货时间:

-

供应能力:

-

付款方式:

-

现在联系
免费会员

联系人 Davis

Ningbo, Zhejiang

现在联系

详情

[Introduction]:

The characteristics of solvent based ink for outdoor printer are easy to be evaporated and fast dry, which clogs the print head very easily. In some condition that the print head clogs more frequently if the ink was mixed some micro impurity. Currently there are 3 ways to clean the print head:

1. Using vacuum cleaner to suck out the built up from outside of the jets.

2. Using syringe with cleaning liquid push out from the inlet of the jet.

3. By ultra-sonic vibrator.

Those 3 above methods will result in

1. Break the edge shape of nozzle.

2. Destroy the piezoelectric crystal inside the jet. 3. Neither cleans the jet at all.

 

 

According to above problems, XAAR **8 printhead Cleaner was developed based on the research of nozzle construction and electric specification. XAAR **8 printhead Cleaner is good for XAAR***8 print jet in non-destroyed cleaning and maintenances by computerized controlled piezoelectric crystal vibration. Generally, it takes *0 minutes to finish whole cleaning process.

 

[Application]:

XAAR **8 printhead Cleaner is applied on XAAR***8 print jet.

[Instructions]:

a. Make sure the power of XAAR **8 printhead Cleaner is off. Connect the XAAR***8 to the XAAR **8 printhead Cleaner. Be sure there is only one side can be connected on the connector of XAAR  **8 printhead Cleaner. Also use the attached PVC tube to connect the inlet of print jet and syringe.

b. Put the print jet in a cleaning liquid vessel for soaking about *0 minutes. The time for soaking is depended on how much remains or how much dry of the jet. Make sure do not put whole jet in the cleaning liquid. Leave the connector on the top.

c. Turn on the XAAR  **8 printhead Cleaner. Then manually slow to pull the syringe first time for about *0ml from the jet. Release the end of the syringe and drain the *0ml liquid if there is micro impurity.

d. Pull out the syringe and pour about *0 to *0 ml of cleaning liquid into the syringe, manually slow pushing the cleaning liquid into jet. Then repeat pulling and pushing manually to clean the jet. Make sure do not pull and push too hard to protecting the inside of jet. Continue this cleaning cycle for about *0 minutes.

e. Turn off the XAAR  **8 printhead Cleaner. Take out the jet from the vessel and disconnect it from XAAR  **8 printhead Cleaner. Using a syringe with cleaning liquid to visual checking the output of the jet to decide whether to continue the cleaning cycle or not.

Specifications

 

Input electricity

AC**0V(**0V)/*0Hz

Voltage

DC5V

Power

*5W

Cleaning Frequency

8KHz

Biggest setting hour

*5minute

Maintain 2 pc of print head at the same time

Package: 1 set Cleaner, 2 PCS of Data line, 2pcs tube, Manual


[Warning]:

a. Make sure the power of XAAR **8 printhead Cleaner is off when connecting or disconnecting the jet to or from the Xaar **8 printhead Cleaner.

b. Cleaning liquid is inflammable, watch out for fire prevention.

c. If there is some lines spread out in different direction when visually checking the after-clean condition. This means some surfaces of nozzles were damaged. This cannot be repaired.

d. XAAR  **8 printhead Cleaner is perfect for clean and regular maintenance. Xaar **8 printhead Cleaner cannot repair the damaged jet.

Send a direct inquiry to this supplier

至:

Davis < NINGBO ALLSIGN TRADING COMPANY LIMITED >

我想知道: