详情
Shuttle loom parts and accessories,***5 and GA**5 woven fabric
machine introduction
Transmission mechanism:
1, transmission mode: single motor V-belt drive
2, control mode: single side switch control clutch and brake
device.
3, clutch type: cone friction disc
4, brake type: steel brake
5, the wheel shaft and crank ratio 1:2
Main bodies and their specifications
First, sent by the agency,Shuttle loom parts and accessories?***5
and GA**5 woven fabric machine introduction
Transmission mechanism:
1, transmission mode: single motor V-belt drive
2, control mode: single side switch control clutch and brake
device.
3, clutch type: cone friction disc
4, brake type: steel brake
5, the wheel shaft and crank ratio 1:2
Main bodies and their specifications
First, sent by the agency
1, type: semi positive semi negative automatic warp, automatic
adjustment of warp tension.
2, a beam axle diameter: **0mm
3, beam disc diameter: **5mm, **0mm
Two, through the parking device
1, type: front and rear swing mechanical menopause
2, the tooth movement cycle: crank shaft rotation 2 times
3, menopause column number: 4 column
Three, opening mechanism
1, type: the inside of the disc mounted on the top of the crane
2, the disc diameter: *2mm
3, heald frame number: 2 page heald frame (can be adjusted to the
plate of the twill or to modify the multi arm lifting device *6
page) (5)
Four, the shuttle mechanism
1, type: under the shuttle
2, the shuttle size: length **3mm, width *4.5mm, high *3.5mm (left
hand)
3, the skin type: movable skin knot
4, leather knot size: long **5mm, wide *0mm, high *2mm
5, at the same time rotor diameter: *6mm
Five, beating up mechanism
In 1, type: crank shaft hand beating
2, crank shaft diameter: *0mm, ***5K diameter of *2mm.
3, crank shaft radius: *6mm
4, crank shaft center distance: ***0mm (***0mm loom), ***4mm
(***0mm loom), ***6mm (***0mm loom), ***9mm (***0mm loom)
5, hand type: bearing type hand
6, hand length: **9mm
7, hand bolt diameter: *5mm,
From 8, hand center to the rockshaft Center: **5mm
9, the rocking shaft type: whole root
*0, shaft diameter: *8mm
*1, reed type: wood structure
*2, shuttle board length: ***3mm (***0mm loom), ***7mm (***0mm
loom), ***9mm (***0 looms), ***2mm (***0mm loom)
*3, box bottom plate length: **1mm side **0mm side switch, the
shuttle magazine.
Six, warp protection device
Type: reed(Shuttle loom parts and accessories)
Seven, coiling mechanism
1, type: seven gear intermittent coiling
2, weft density range: ****2 root /cm
3, the diameter of the piercing roller: **7mm
4, guide cloth roller diameter: *2mm
5, roller diameter: *5mm
Eight, the extension device
1, type: single row copper ring roller
2, only a few: around 1 groups
3, the weft shear hammer: the role of the role of the hammer
Nine, broken weft stop device
1, type: weft cam control side weft fork or point peck type
weft
2, coiling and rewinding device
Ten, weft feeding device
1, type: automatic shuttle type
2, the shuttle magazine: vertical in-line
3, shuttle storage capacity: *0
4, change the shuttle to induce a device: adopt the probe to change
the shuttle to induce the device (to the request not high of the
fabric also can use the weft fork to change the shuttle to induce
the device)
5, shuttle safety device: when the shuttle mechanism failure,
immediately stop, avoid the machine rolling loss
6, free shuttle, shuttle side parking device: Suokunei shuttle or
shuttle position on the side, immediately stop automatically
7, prevent residual weft weaving device: can avoid the burr, double
weft defects, improve the quality of fabric,Shuttle loom parts and
accessories
Eleven, the main equipment and specifications
1, weft tube: total length **0mm, head diameter *7mm
2, steel reed, total length ***4mm (***0mm loom), ***8mm (***0mm
loom), ***9mm (***0mm loom), ***3mm (***0mm). Height: **0mm
3, heald length: plain or twill **5mm, dobby **0mm
4, menopause tablets: length **0mm, width *1mm, closed
5, triangle belt: A type ***6
