详情
RoboCT spray disinfection robot product
Introduction
RoboCT UV disinfection robot integrates two disinfection and
sterilization methods of
UV and air filtration. By destroying the molecular structure of DNA
(deoxyribonucleic
acid) and RNA (ribonucleic acid) of microbial cells, it causes the
death of growth cells
and / or regenerative cells, so as to achieve the effect of
sterilization and disinfection. At the same time, combined with
autonomous navigation and dynamic obstacle avoidance functions, the
robot can achieve large space, intelligent, autonomous, multi
track, fixed-point timing killing.
1、Product features
1. Strong sterilization and disinfection ability
2. Large workspace
3. Make use of self moving chassis to realize unmanned work
4. Wide range of sterilization, no harmful residue
2、Application scenario
1、Medical institutions: isolation bed, operating room, waiting
room
2、Transportation hub: airport, railway station, bus station
3、Enterprise unit: office area, public area
3、Product parameters
| Technical item |
Technical Requirement |
| Appearance design |
1. Shell: PC + ABS, stainless steel, easy to wipe,
antibacterial
2. Size: 540mm * 580mm * 1740mm |
| Hardware Parameters |
1. Processor: integrated Intel ® J1900 quad core processor
2.0GHz
Chipset: Intel ® Bay trail SOC chipset
2. Autonomous navigation: no less than 3 kinds of sensors (LIDAR /
odometer / gyroscope) can be used
Multi-sensor fusion navigation scheme based on
3. Intelligent obstacle avoidance: the robot can avoid obstacles
flexibly and avoid obstacles normally under low light
conditions
4. Motor torque 8.1nm (high load, low power consumption)
5. The chassis adopts shock absorption suspension system, which can
effectively guarantee the stability of chassis operation. |
| Operating Parameters |
1. Movement speed: 0.45m/s (in navigation state)
2. High precision laser positioning, laser measurement accuracy: ±
2cm
3. Steering performance: 360 °, 0 radius turning
4. Regular working hours ≥ 4 hours
5. Be able to move autonomously to achieve autonomous navigation,
obstacle avoidance and other functions
6. During the robot\'s task execution, it supports the pause mode,
and can continue to execute without ending after resuming
task
7. The robot can control the automatic switch of the electric door
through the Internet of things
8. Support the expansion of elevator control scheme, and realize
multi floor operation across regions.
9. There is no need to make secondary transformation to the
environment, no need to install route and positioning mark device,
and the robot is in operation
Autonomous Navigation
10. The robot has the function of automatic recharging, which
supports the automatic recharging of low power and can perform
tasks circularly
11. Support the automatic detection in the working area, and
automatically turn off the ultraviolet lamp irradiation after
detecting the personnel.
|
4、Factory and qualification
5、Precautions
(precautions)
-Avoid placing the machine in a wet place, and a large amount of
water vapor will enter the motor components through the gap.
-When you stop working, please turn off the power of the motor,
safety first.
-Do not use in dusty places.
(instructions for regular maintenance)
-Wipe the surface of perpendicularity adjusting part to avoid
affecting the accuracy.
-Adjust the verticality adjusting parts regularly to ensure that
the tire is in a vertical state.
-Before each start-up, the sundries within the operation range of
the machine must be removed with an air gun, the power supply must
be connected, the machine must be started, and the operation
condition of the machine must be checked.
-Check whether the fastening screws are loose.
-If the machine is not used for a long time, please wipe it clean
and put it in a dry and ventilated environment. Do not store it in
a place with high temperature and humidity.
--Every season, the motor bearing needs to be replaced with oil to
ensure that the
motor runs without resistance.
-Every season, the oil of shock absorption bearing needs to be
changed to ensure the smooth running of tire.
6、 After sales service
1. Our company can provide installation, debugging and technical
training for all our products.
2. After the installation and commissioning, the warranty period is
one year (except for vulnerable parts and artificial damage), with
a lifetime warranty.
3. Irregular on-site maintenance, on-site operation and technical
training.
4. After sales contact: 0571-89167832.
5. Service content: in case of equipment failure, first communicate
by phone. If the problem cannot be solved, our company will rush to
the site as soon as possible to solve the problem. After sales
service includes not only equipment maintenance, but also technical
support. Our technicians can carry out on-site technical training
and provide a complete set of solutions. Professional and technical
personnel shall follow up the use of user\'s equipment at any
time.
