431 Stainless Steel Hex Bar Round Bar

详情

Description

 
 

**1 is a high chromium-low nickel high hardenability Martensitic stainless steel with high strength and good corrosion resistance, as generally supplied hardened and tempered in the tensile range **0 - ***0 Mpa (condition T) Brinell range **8 - **2.Characterised by very good corrosion resistance in general atmospheric corrosive environments, good resistance to mild marine and industrial atmospheres, resistant to many organic materials, nitric acid and petroleum products coupled with high tensile and high yield strength plus excellent toughness in the hardened and tempered condition. **1 due to its excellent hardenability is capable of being through hardened up to Rc*4, depending upon carbon content and section size. Small sections can be air cooled and larger sections oil quenched for maximum through hardness.Pre hardened and tempered **1 will also respond readily to nitriding achieving a typical surface hardness of over Rc*5. The nitriding process however reduces the corrosion resistance and is therefore not generally recommended except for critical applications where the benefit outweighs all other considerations.

 
 

 

 
 

Table1：

 
 

 

 



































 

UNS Designati-onsB	Type	Composition,% max
		C	Mn	P	S	Si	Cr	Ni	Mo	N	Other elements
S****0	**1	0.2	1.0	0.*4	0.*3	1.0	****7	1.***2.5	...	...	.....

 
 

 

 
 

 

 
 

Table2:

 
 

Typical Mechanical Properties At Room Temperature - *Hardened and Tempered to Condition T

 
 

 

 



























 

Tensile Strength Mpa	**0
0.2% Yield Strength Mpa	**0
Elongation in *0mm %	*9
Impact Izod J	*5
Hardness	HB	**0
	RC	*0

 













 

*Typical Hardening Temperatures	**0oC - ***0oC
*Typical Tempering Temperatures	**0oC - **0oC
	**0oC - **0oC

 

 

 

 
 

Table3:

 
 

Typical Mechanical Properties At Room Temperature - Hardened By Oil Quench at **0oC and Tempered as Indicated 

 

























































 

Tempering Temperature C	**0	**0	**0	**0	**0
Tensile Strengt Mpa	***0	***0	***0	**0	**0
0.2% Yield Strength Mpa	***0	***0	***0	**0	**0
Elongation in *0mm %	*6	*6	*6	*5	*0
Impact Izod J	*4	*4	**5	**5	*0
Hardness	**0	**0	**5	**5	*0
	*4	*5	*6	*2	*9

High tensile strength and high yield strength with slightly lower impact properties when tempered below **0oC. Section Size *0mm

 

 

 
 

*Note drop in impact properties.Tempering within the range **0oC - **5oC should be avoided. 







Related Specifications

 
 

 

 




























 

Grade	UNS No	Old British		Euronorm	Swedish	Japanese
		BS	En	No	Name	SS	JIS
**1	S****0	**1S*9	*7	1.***7	X*7CrNi***2	***1	Sus**1

 
 

 

 
 

 

 
 
 
 

 

 
 

Mechanical Requirments

 
 

Mechanical Properties: Tensile strength  (MPa): quenching and tempering, min***0

 
 

elongation 5 (%): quenching and tempering, min*0

 
 

impact energy Akv (J): quenching and tempering, min*9

 
 

Hardness: annealing, min**5HB

 
 
 
 
 
 

 

 
 

 

 
 

 

 
 

Mechanical Properties

 
 

The mechanical properties for grade **1 stainless steels are listed in the table below.The bend test is obtained around a diameter of the bend factor multiplied by the steel thickness.

 
 

AUnless otherwise indicated,a grade designation originally assigned by the American Iron and Steel Institute(AISI).

 
 

BYield Strength shall be determined by the offset method at 0.2% in accordance with Test Dethods and Definitions A**0 .Unless otherwise specified (see Specification A**0/A**0M,paragraph 4.1.*1,Ordering information),an alternative method of determining yield strength may be based on total extension under load of 0.5%.

 
 

C Either Brinell or Rockwell B Hardness is permissible.

 
 

DBend tests are not required for chromium steels(ferritic or martensitic) thicker than 1 in.

 
 

[*5 mm] or for any austenitic or duplex(austenitic-ferritic)stainless steels regardless of thickness.

 
 

 

 
 

 

 
 

Key Properties:

 
 

The specified properties are for bar products in ASTM A**6. The properties may not be necessarily similar to other forms such as forgings and plates.

 
 

Maching:

 
 

**1 machines best in the hardened and tempered as supplied condition and is regarded as being readily machineable with all operations such as turning and drilling etc. capable of being carried out satisfactorily. It does not work harden to the same extent as the **0 series austenitic stainless steels, but is more similar in this respect to the low alloy high tensile steels such as ***0 etc.Allowing therefore for its high tensile properties, all machining should be carried out as per machine manufacturers recommendations for suitable tool type, feeds and speeds.

 
 

Welding:

 
 

**1 is not generally recommended for welding in either the annealed or hardened and tempered condition, due to its air hardening capability which can lead to the formation of brittle martensite, resulting in cold cracking due to contraction stresses within the weld and heat affected zone. The higher the carbon content the higher the hardening capability and the greater the risk of cracking.Pre heating and interpass temperature control during welding, plus very slow cooling and post-weld annealing is the best method to prevent cracking.

 
 

Welding Procedure:

 
 

Welding electrodes or rods should be low hydrogen types **0 or *similar when good strength is required otherwise an austenitic stainless electrode or rod such as **8 or *similar may be used resulting in a more ductile weld when strength is not so critical and post-weld annealing is not possible or intended.Pre-heat at **0oC - **0oC and maintain interpass temperature at **0oC minimum. On completion of welding cool slowly as possible until hand warm if possible: Post-weld sub-critical anneal at **0oC - **0oC, and cool in air.*Please consult your welding consumables supplier.

 
 

Applications

 
 

 

 
 

 

 
 

• · 1).Laboratory equipment
• · 2).Marine systems
• · 3).Beater bars
• · 4).Pump and propeller shafts
• · 5).Nuts and bolt.
•  

国家:	China
型号:	431 stainless steel bar
离岸价格:	( Negotiable ) （面議） 获取最新报价
位置:	Wuxi China
最小订单价格:	-
最小订单:	100 Kilogram
包装细节:	seaworthy standard , or as required
交货时间:	15 to 20 days
供应能力:	1000 Ton per Month
付款方式:	Money Gram, Western Union, D/P, D/A, L/C, T/T
產品組 :	stainless steel bar