详情
Worm Gear Screw Jack,Right Angle
Gearbox,Lift Table.
Worm Gear
Screw Jack Lift systems are ruggedly designed and produced in
standard models with load handling capacities from 1/4 ton to **0
tons. They may be used individually or in multiple arrangements.
There are no "standard" travel lengths and all Worm Gear Screw
Jack Lift systems are built to specification. Multiple Worm Gear
Screw Jack Lift systems arrangements include In-Line
Configuration Worm Gear Screw Jack Lift systems, H Configuration
Worm Gear Screw Jack Lift systems, U Configuration Worm Gear
Screw Jack Lift systems, T Configuration Worm Gear Screw Jack
Lift systems.
Worm Gear Screw Jack Lift systems
parts include worm gear screw jacks, right angle miter gearbox,
jaw type and flex type couplings, linking bars, electric motor /
geared motor, When long distance between jack and jack, extra
additional pillow block bearings. For lightweight and short
stroke adjustment, manual operation Worm Gear Screw Jack Lift
systems is avaiable. Compared with pneumatic cylinder systems,
air cylinder lift systems or hydraulic table lift system.
Multiple Worm Gear Screw Jack Lift systems arrangements have
heavy duty-load capacity up to several hundreds tons, self
locking-no need brake mechanism or others locking systems,
precision positioning-easy to control according to your own
design, synchronizing lifting-multi-units uniform travel speed,
easy installation, maintenance free and long service
life.
Two Worm Gear Screw Jack Lift
Systems Efficiency *5%
Inline Configuration Screw jack
lift systems with two worm gear screw jacks, two flexible
couplings, one linking bar and one motor. T Configuration Screw
jack lift systems with two worm gear screw jacks, five flexible
couplings, two linking bars, one right angle bevel gear box
three-way and one motor.
Three Worm Gear Screw Jack Lift
Systems Efficiency *0%
Inline Configuration Screw jack
lift systems with three worm gear screw jacks, five flexible
couplings, two linking bar and one motor. T Configuration Screw
jack lift systems with three worm gear screw jacks, nine flexible
couplings, four linking bars, two right angle bevel gear boxes
three-way and one motor.
Four Worm Gear Screw Jack Lift
Systems Efficiency *5%
H Configuration Screw jack lift
systems with four worm gear screw jacks, three right angle bevel
gear boxes three-way, *3 flexible couplings, six linking bars and
one motor. U Configuration Screw jack lift systems with four worm
gear screw jacks, three right angle bevel gear boxes three-way,
*1 flexible couplings, four linking bars and one
motor.
Six Worm Gear Screw Jack Lift
Systems Efficiency *0%
H Configuration Six Screw jack
lift systems with six worm gear screw jacks, three right angle
bevel gear boxes three-way, *7 flexible couplings, eight linking
bars and one motor. 2H Configuration Six Screw jack lift systems
with six worm gear screw jacks, three right angle bevel gear
boxes four-way, *7 flexible couplings, eight linking bars and one
motor. U Configuration Six Screw jack lift systems with six worm
gear screw jacks, three right angle bevel gear boxes three-way,
*5 flexible couplings, six linking bars and one
motor.
Eight Worm Gear Screw Jack Lift
Systems Efficiency *0%
H Configuration Six Screw jack
lift systems with eight worm gear screw jacks, three right angle
bevel gear boxes three-way, *1 flexible couplings, *0 linking
bars and one motor. 2H Configuration Six Screw jack lift systems
with eight worm gear screw jacks, seven right angle bevel gear
boxes three-way, *9 flexible couplings, *4 linking bars and one
motor.
Worm Gear Screw Jack Lift Systems
Parts 1 – Worm Gear Screw Jacks
Worm Gear Screw Jack Lift Systems
Parts 2 – Right Angle Bevel Gear Boxes
Worm Gear Screw Jack Lift Systems
Parts 3 – Jaw Type And Flex Type Couplings
Worm Gear Screw Jack Lift Systems
Parts 4 – Linking Bars
Worm Gear Screw Jack Lift Systems
Parts 5 – Pillow Block Bearings
Worm Gear Screw Jack Lift Systems
Parts 6 – Electric Motors / Geared Motors
Worm Gear Screw Jack Lift Systems
Parts 7 – Geared Motors
Installation Of Worm Gear Screw
Jack Lift Systems:
Direction of rotation: Before
starting installation work, the direction of rotation of all worm
gear screw jacks, right angle bevel gear boxes and the drive
motor must be checked with regard to the feed direction of each
individual worm gear screw jack.
Alignment errors: All components
must be carefully aligned during installation. Alignment errors
and stresses increase power consumption and lead to overheating
and premature wear. Before a drive unit is attached, each worm
gear screw jack should be turned through its entire length by
hand without load. Variations in the amount of force required
and/or axial marks on the outside diameter of the screw indicate
alignment errors between the worm gear screw jack and its
additional guides. In this case, the relevant mounting bolts must
be loosened and the worm gear screw jack turned through by hand
again. If the amount of force required is now constant
throughout, the appropriate components must be aligned. If not,
the alignment error must be localized by loosening additional
mounting bolts.
Test run: The direction of
rotation of the complete system and correct operation of the
limit switches must be checked again before attaching the drive
motor. In the case of translating screw jack, check that the
screw is lubricated with grease from the interior of the gear box
and re-lubricate if necessary. In the case of travelling nut
rotating screw jack, the jack screw should be coated with
suitable grease to provide lubrication for lifting operation. The
first test runs can then be carried out without load. A maximum
operating time of *0 % can not be exceeded at trial runs under
weight for worm gear screw jacks with trapezoidal
screws.
Operation: The loads, speeds and
operating conditions specified for the worm gear screw jacks and
transmission components must not be exceeded even
briefly.
Worm Gear Screw Jack Lift Systems
Application Cases In Pakistan:
Per screw jack lift systems parts
includes 4 pcs 5t travelling nut rotating screw jacks, 2 pcs 1:1
ratio right angle bevel gear boxes, 5 pcs linking bars, *1 pcs
couplings, 4 pcs steel plates, 4 pcs flange type pillow block
ball bearings, 1 electric motor and 2 sets forward &
reversible switches and contractors.
The linking bars, worm shafts of
jacks, & output shafts of gear boxes, output shaft of
motor must be are installed and aligned. So all parts center
height must be same, jt*5 gear boxes are *0 mm, 1.5kw motor is *0
mm, jacks are *1.5 mm matching steel plate thickness *8.5mm,
equal to *0 mm. So the main three parts center height is same
with *0 mm. Easy to install them inline alignment.
The screw jack lift systems
position is ***7.5x***7.5mm, included all safety factors, max.
loading capacity ***0kg, travel stroke up to ***8.5 mm, after
calculation, lifting screw total length ***2.5 mm. Lifting speed
about **5 mm/min. Because lifting screw is very long, assured the
whole lift system stable for linear motions, at the top end,
extra additional 4 pcs flange type pillow block ball bearings to
fix the long lifting screws, and extra additional guiding
supports for the lift system.
Rotating jacks model:
JTW*5T-UR****8.*-L-I-C-N
Steel plate model:
T*8.*-JTW5T
Gear boxes model:
JT***1:*****0R****0R-I-LR-B3,
JT***1:*****0R****0R-I-LR-O-B3
Flange type ball bearing model:
UCF**4
Jaw coupling model:
FL*4/*8
Linking bars model: D*5L**2.*5,
D*5L**1.5
Electric motor model:
TC**0L**-B**1.5kw
2 set forward & reversible
switches and contractors to control jacks lift system lifting up
and down.
Application in steel, pipe, tube,
plate, roll forming roller adjustment, feeder straightener rolls
adjustment, adjusting synchronous coil feed lines rolls,
precision roller leveler, coil sheet slitter line, paint coating
line, cut to length line, tension levelling line, continuous
galvanizing line, beverage production line, foam concrete cutting
machine, sanding machine, heavy vehicles mobile lifting platform,
bottle monitoring system height adjustment, conveyor adjustment,
plate saw angle adjustment, spray infeed conveyor lift system,
theatre stage lifting platform, solar tracker, satellite dish
antenna azimuth, raising sluice gate, screw scissor lift table,
synchronized lifting system, food processing lifting system,
extrusion machine, cnc steel leveling machine, blow molding
machine, curing oven lifts, bolted tank, steel shuttering
concrete beams adjustment, vintage industrial crank desk, solar
panel tracking system, railway maintenance lifting jack, damper
adjustment, continuous casting, cnc cut to length machine,
robotics arm raising, palletizer, extrusion machine, motorized
self-raising tower system, angle tilt adjustments with double
clevis, aircraft docking system, open and close flood gates,
metallurgy industry, mining industry, chemical industry,
construction industry and irrigation
industry.
| 国家: |
China |
| 型号: |
depends on lift table load capacity and platform sizes
|
| 离岸价格: |
100 ~ 1000 / Set （面議）
获取最新报价
|
| 位置: |
- |
| 最小订单价格: |
100 per Set |
| 最小订单: |
1 Set |
| 包装细节: |
compact export plywood case |
| 交货时间: |
15 days |
| 供应能力: |
1500 Set per Month |
| 付款方式: |
Money Gram, Western Union, T/T |
| 產品組 : |
Screw Jack Lift Table
|
